Mr. Wayne S. MOORE, P.E.
Senior Civil/Structural Engineer
Mr. Moore has a BS degree in Civil Engineering, an MS degree in Structural Engineering and is a multi-state Registered Professional Engineer. His experience spans over 30 years and has included preliminary/schematic (Title I) and final (Title II) analysis and design, construction administration/support (Title III) services and expert witness service for government, industrial, commercial, institutional and residential clients. Mr. Moore is proficient in the static and dynamic analysis of structures subjected to natural phenomena (wind and seismic) loads and has authored a publication entitled Wind Design Loads for Temporary Structures. He is a licensed HUD FHA Structural Inspector and is knowledgeable of all applicable building codes and criteria including the IBC, IRC, UBC, CABO as well as those developed by ASCE, ACI, NCMA, AASHTO, AITC, OSHA, USDOE, UFC and AREA. Mr. Moore is active in technical and civic organizations including the American Society of Civil Engineers, the National Society of Professional Engineers, the South Carolina Structural Engineers Association, American Institute of Steel Construction, Rotary International and Habitat for Humanity. Mr. Moore is a certified GSWCC Level II design professional.
Mr. Phillip D. HART, P.E.
Mr. Hart has a BS degree in Civil Engineering Technology and is a registered professional engineer in GA, SC, and NC. He has over 11 years of experience in the design and analysis of new, renovated and restored sructures. This includes design and analysis for various commercial, residential, industrial, and government projects. He has been responsible for structural steel, reinforced concrete, masonry and timber design, seismic analysis, construction site inspections and field walk downs. Mr. Hart is adept at structural analysis software including STAADPro, Enercalc, ConCAD, BeamChek, NCMA Masonry and others. He is experienced with commercial building codes including IBC, IRC, UBC as well as other cited design criteria including those published by ASCE, ACI, NCMA, AASHTO, OSHA and AITC. Mr. Hart is a licensed IBC Chapter 17 Inspector in the state of South Carolina.
Ms. Jessica MOORER
Junior Civil/Structural Engineer
Ms. Moorer has a BS degree in Civil Engineering Technology. She has three years of experience in field fabrication with an emphasis on CAD identification, inventory and procedure development. She is responsible for performing civil and structural calculations for various commercial, industrial and government clients. Projects have included structural and cold-formed steel building, cast-in-place concrete footing, reinforced masonry, elevated concrete slab and reinforced concrete bridge abutment analysis and design.
Mr. Aric McBRIDE
Junior Mechanical/Structural Engineer
Mr. McBride has a BS degree in Mechanical Engineering. He is knowledgeable of AutoCAD and MathCad software. He assists in projects involving mechanical/structural engineering such as static and dynamic seismic and wind analysis of HVAC equipment/curbing, electrical/telecommunications and mechanical equipment supports, motorized and non-motorized doors/supports as well as other building and non-building components/cladding and equipment.
Mr. Lawrence TAN
Mr. Tan has a BS degree in Architecture. He has over 18 years of design experience in multiple engineering disciplines including architectural, structural, electrical and plumbing. He is proficient in AutoCAD and SketchUp. He is responsible for structural steel, cold-formed steel, reinforced concrete, masonry and timber design, technical specification writing, conceptual design and feasibility study report writing and construction site inspections.
Mr. Anthony THOMAS
Mr. Thomas has a BS degree in Civil Engineering Technology with a focus on project management. He has over 18 years of land surveying and design experience with an emphasis on Civil/Site design. He is proficient in AutoCAD and is responsible for the design of various commercial and industrial projects.
Mr. Jonathan GRAY
Civil/Structural CAD Designer
Mr. Gray has an AS degree in General Technology with an emphasis in Industrial Drafting. He has almost 10 years of drafting and design experience in the civil engineering field. Mr. Gray is proficient in multiple software design programs including AutoCAD, Land Desktop, Civil 3D and ArcView 9.3. He is responsible for generating plans associated with civil/site and structural design.
Mrs. Deborah H. MOORE
Mrs. Moore, has a BS degree in Applied Organizational Management and an AS degree in Chemical Engineering Technology. Her experience spans over 25 years in Quality Assurance/Control, Standards/Procedures Development and personnel training. She has worked with staff and management for government and private sector clients to develop and implement QA/QC procedures and develop time-saving and cost-effective standards and procedures. She has developed training programs and trained personnel in support of industrial and environmental engineering projects.
Mrs. Lynne CHARLES
Mrs. Charles has an AS degree in Applied Science with a major in accounting and a certificate in Business Management. She has over 13 years of office management and accounting experience. She also has experience as a certified safety coordinator. Mrs. Charles is proficient in QuickBooks, Peachtree, Oracle, Microsoft Outlook, Excel, PowerPoint, and Word.
Ms. Whitney HODGES
Senior Administrator Assistant